World Water Day April-2011 96 SUSTAINABLE MANAGEMENT OF TEXTILE WASTE WATER OF PAKISTAN By Dr. Muhammad Khalid Iqbal, Sameer Ahmed, Dr. Shazad Alam and Dr. Munir Ahmed1 ABSTRACT Colour removal, especially from textile waste water s, has been a big challenge over the last decades, an d upto now there is no single and economically attractive treatment that can effectively decolourise dyes. In the past years, notable achievements were made in the use of biotechnological applications to textile waste waters not only for colour removal but also for the complete mineralization of dyes. Different microorganisms such as aerobic and anaerobic bacteria, fungi and actinomycetes have been found to catalyse dye decolourisation. Moreover, promising results were obtained in accelerating dye decolouri sation by adding various techniques. This paper provides a critical review on the current technologies available for decolourisation of textile waste water s and it suggests effective and economically attractive alternatives. Nomenclature Parameters Abbreviations BOD Biological Oxygen Demand COD Chemical Oxygen Demand TSS Total Suspended Solids TDS Total Dissolved Solids 1-INTRODUCTION Textile industry is the backbone of Pakistan economy and is one of the most important and largest industrial sector s of Pakistan with regard to production source of foreign exchange and labour employment. It alone accounts for 65% of the country ’s export, 46% of industrial production 38% of employed industrial work force and 9% of gross national product (Iqbal, et al., 2007). With the increased demand for textile products, the textile industry and its waste water have been increasing proportionality, making it one of the main sources of sever e pollution problems worldwide (Santos, et al., 2007).In particular, the release of dyes into waste waters by various industries is environmental issue due to various dyes’ persistent and recalcitrant nature. Textile industries are responsible for the discharge of large quantities of dyes into natural waterways due to inefficiencies in dyeing techniques. Up to 50% of dyes may be lost directly into waterways when using reactive dyes (McMullan et al., 2001). ______________________________________________________________________________________ 1. PCSIR Laboratories Complex Lahore, NCBA & E Lahore. World Water Day April-2011 97 The presence of dyes in waterways is easily detectable even when re leased in small concentrations. This is not only unsightly, but the colouration of the water by the dyes may have an inhibitory effect on photosynthesis affecting aquatic ecosystems. Dyes may also be problematic if they are broken down anaerobically in the sediment, as toxic amines are often produced due to incom plete degradation by bacteria . The breakdown products of dyes are toxic and muta genic to life (Weisburger, 2002). Different fig ures showed the real picture of contamination. Fig:1 Different out lets of Industrial Waste Water World Water Day April-2011 98 The fibers used in the textile industries can be divided into two types: nat ural and man- made. The two major natural fibers are wool and cotton. The most important man -made fibers include polyester, rayon, nylon, polyacrylic and polyamide. It appears that most of the textile effluents do not have high BOD content, but they do have large pH and color variations. Besides, polyvinyl alcoho l (PVA), starches and various surfactants may also appear in many dyeing waste effluents. These compounds are chemicals widely used in the dyeing and sizing operations. They have a high COD content o f over 10,000 mg/1 and can contribute considerably to overall COD content of the textile waste effluents. The normal dyeing operations of a textile plant are such that the dye used varies from day to day and sometimes even several times a day, primarily because of the batchwise nature of the dyeing process. Dye changes cause considerable variation in the waste characteristics, particularly pH. A large pH swing is especially troublesome primarily because the pH tolerance of conventional biological and chemical treatment systems is very limited. Hence without proper pH control, normal operation of these treatments is essentially impossible. Along with the high pH variation, the textile waste effluents also have a relatively high temperature. In several steps of the dyeing operation, hot rinse waters of up to 90°C are used, resulting in a final effluent temperature between 35°C and 40°C. This necessitates proper heat dissipation of the hot effluent prior to other treatments. Strong color is the component of the textile waste effluent which is the most difficult to treat, as men tioned earlier. The combination of strong color and high dissolved solid content leads to high turbidity of the waste effluent. The dyestuffs are highly structured polymers and very difficult to decompose biologically. Hence there is little decomposition of these molecules in the activated sludge process. A strong effluent color, if not removed, will cause considerable disturbance to the ecological system of the receiving waters. Depending on the sources, the dye waste effluent varies considerably in color, suspended solid content and COD concentration. The dye waste effluents varied in color from purple, dark red, brown, grey, dark blue or black. 1.1- PROCESSING OF TEXTILE Textile production involves a number of wet processes. Each process generates waste water containing different types of pollutants. Finishing and drying processes generate volatile organic compound. Dyeing and printing processes produce waste water – containing toxic organic compound such as phenols and also impart highly concentrated color and copper, chromium metals. Bleaching of fibers adds halogen, makes the waste water alkaline. Desizing step in textile process contributes 50 % increase of BOD load. Wool processing may release pathogenic germs. Sometimes pesticides are used for the preservation of natural fibers. These pesticides are discharged into waste water during washing and scouring process. Chemicals present in finishing waste water are highly variable due t o the broad range of finishers available, which generate pollutants of natural and synthetic polymers. The biodegradable organic compound can cause deficiency of dissolved oxygen in receiving water bodies and have a direct effect o n aquatic life (Dos Santos et al., 2006). World Water Day April-2011 99 2- TREATMENT PROCESSES In the following items we have tried to cover the physical, chemical and biological process for the treatment of waste water. It is worth to mention that this review gives the special attention to waste water treatment by physical, chemical and biological process. 2.1-BIOLOGICAL TREATMENT 2.1.1 BACTERIA From the textile effluent different aromatic compounds are produce d and these are susceptible to biological degradation under aerobic and anaerobic conditions. Unde r aerobic conditions, the enzymes mono-and di-oxygenates catalyze the incorporation of oxygen from O2 into the aromatic ring of organic compounds prior to ring fission (Madigan et al., 2003). Although azo dyes are aromatic com pounds, their substituents containing mainly nitro and sulfonic groups, are quite recalcitrant to aerobic bacterial degradation (Claus et al., 2002). This fact is probably related either to the electron -withdrawing nature of the azo bond and their resistance to oxygenases attack, or because oxygen is a more effective electron acceptor, therefore having more preference for reducing equivalents than the azo dye (Chu ng et al., 1993 ). How ever, in the presence of specific oxygen -catalysed enzymes called azo reductases, some aerobic bacteria are able to reduce azo compounds and produce aromatic amines . 2.1.2-FUNGI The capacity of fungi to reduce azo dyes is related to the formation of exoenzymes such as peroxidases and phenol oxidases. Peroxidases are hemoproteins that catalyse reac tions in the presence of hydrogen peroxide (Duran et al., 2002). Lignin and manganese peroxidases have a similar reaction mechanism that starts with the enzyme oxidation by H2O2 to an oxidized state during their catalytic cycle. Afterwards, in a mechanism involvin g two successive elec tron transfers, substrates such as azo dyes reduce the enzyme to its original form (Stolz, 2001). Eighteen fungal strains able to degrade lignocellulosic material or lignin derivatives were tested with the azo dyes . 2.1.3-ENZYME TECH NOLOGY Laccase are copper -containing enzymes that have very broad sub strate specificity with respect to electron donors, e.g. dyes (Abadulla et al., 2000). However, despite the fact that lac cases from T. versicolor, Polyporus pinisitus and Mycelioph thora thermophila were found to decolourise anthraquinone and indigoid -based dyes at high rates, the azo dye , Direct Red 29 (Congo Red) was a very poor substrate for laccases (Claus et al., 2002). Chivukula and Renganathan (1995) cited that the azo dye must be electron -rich to be suscepti ble to oxidation by laccase of Pyricularia oryzae. This situ ation is suitable for the generation of a phenoxy radical, with consequent azo bond cleavage, and th e release of molecular nitrogen. The addition of redox media tors h as been shown to further extend the substrate speci ficity of laccases with regard to several dye classes, although redox mediators can also be formed from laccase oxidation of phenolic azo dyes (Claus et al., 2002). The complete flow sheet of waste water treatment plant is shown Fig -2. World Water Day April-2011 100 Fig:2: Flow sheet of waste water treatment plant 2.1.4 -ACTIVATED SLUDGE REACTOR MODEL 2.1.4.1-Feeding tank 30 liters capacity plastic drum with an outlet fixed at 3 mm above its bottom t o stop the flow of solid to the aeration tank. There is a plastic tube to ensure proper and regular supply of untreated settled waste water from feeding tank to aeration tank. 2.1.4.2-Pinching cock It regulates the flow of settled waste water into an aeration tank, and is installed on the plastic tube. 2.1.4.3-Air pump This pump provides sufficient supply of oxygen not only to meet biological oxygen requirements but also to keep suspended solids and activated sludge in suspension. It World Water Day April-2011 101 also helps to conta ct between microbes and organic matter which is necessary for efficient treatment of waste water. 2.1.4.4-Aeration tank It is simple locally fabricated plastic tank of dimension 20 cm x 15 cm x 29 cm. Working depth of aeration unit was maintained 17.5 c m. The working volume was 6.5 liter. The diffuser was placed at a depth of 25-50 mm above the bottom of tank. 2.1.4.5-Final Clarifier The final clarifier is separated from aeration tank by a glass plate, which acts as a weir to discharge flows to the fin al clarifier. The size of clarifier is 15 cm x 10 cm x 29 cm. (Fig- 2) 2.1.5-TREATMENT OF WASTE WATER BY ACTIVATED SLUDGE REACTOR During study , the conventional activated sludge rector reduced the BOD 5 and COD contents of the effluents to the limits in the NEQS in about 10 days retention time. The main reason to take longer time to treat the waste water may be due to inherent disability of microbes to break down the dyes rapidly. Dyes are complex organic matter that requires long time to decompose by micro bes. Dyes colour also limits the penetration of light hence hindering microbial growth and activities. To overcome these problems it is common practice to pre – treat textile waste water either by using coagulants or adsorption techniques before biological treatment (Lina et al ., 2006). Activated carbon, Sand, and Brick power were used as absor bents to treat the textile waste water. Table-1 shows the removal efficiency of activated carbon. It removes the dyes colour of sample due to great absorption capacity. Activated carbon proved a very good material to treat the waste water. The average BOD5 and COD removal percentage was 63% and 59 % respectively. Total solids such as TDS and TSS average content were found to be reduced to 44% and 41% respectively. Treated carbon also resulted in 10% reduction in the P H. Activated carbon was very effective to remove BOD 5 and COD contents and could not be cost effective. (Turan, 2001). Table-1. Performance of Activated Carbon Parameters Sample No 1 Sample No 2 Influent Effluent Removal % Influent Effluent Removal% PH 10.5 9.6 8.6 10.8 9.7 10 TempC0 38 25 — 40 30 — BOD5 588 223 62 640 230 64 COD 1528 627 59 1556 622 60 TDS 4250 2423 43 4560 2508 45 TSS 320 195 39 370 155 42 (Iqbal et al., 2007) World Water Day April-2011 102 2.1.5.1-BIOLOGICAL TREATMENT OF WASTE WATER PRE-TREATED WITH ACTIVATED CARBON Presence of dyes in the textile waste water was found to be major hindrance in the growth of bacteria because of their characteristics such as colour and toxicity. However waste water treated with activated carbon appeared to be almost transparent, hence promoted the growth of the bacteria. Consequently, the efficiency of biological treatment was significantly enhanced. It was noted that activated carbon acted as a good absorbent for dyes compounds as well. Table-2. Biological treatment of waste water pre-treated with Activated carbon (Iqbal et al., 2007) R.T= Retention Time Table-2 indicates that four days retention time resulted in more than 87% removal of BOD5 . It is apparent from the results that six days retention time has lowered the BOD 5 content to half of the limit s provided in the NEQS. It is important to mention that biological treatment of waste water pretreated with activated carbon was resulted in 50% reduction in retention time and 27% increase in the removal efficiency of biological process, when compared wit h the results of biological treatment of untreated waste water. (Lina et al., 2006). 2.2-PHYSICAL TREATMENT 2.2.1-PERFORMANCE OF SAND The efficiency of sand filter in treating textile waste water was not appeared to be significant as evident in table -3. The average removal of BOD 5 and COD content was found to be 34% and 32 % respectively. For TDS and TSS the average removal varied from 12.5% and 30%. Since sand as absorbent material was not found to be efficient. It was inferred that biological treatment of effluent pretreated sand was not feasible. (Turan, 2001). Table-3. Performance of Sand Parameters Sample No 1 Sample No 2 Influent Effluent Removal % Influent Effluent Removal% PH 10.5 10.3 1.9 10.8 10.5 2.7 TempC0 38 22 — 40 28 — BOD5 588 382 35 640 429 33 COD 1528 1024 33 1556 1089 30 TDS 4250 3612 15 4560 4104 10 TSS 320 224 30 370 157 30 (Iqbal et al., 2007) R.T(days) BOD5 (mg/l) COD (mg/l) Influent Effluent Removal % Influent Effluent Removal% 2 223 134 77.2 627 389 74 4 223 78 87.2 627 232 85 6 223 49 92 627 144 90 World Water Day April-2011 103 2.3-CHEMICAL TREATMENT 2.3.1- TREATMENT OF WASTE WATER WITH LIME The commercial lime was used as coagulant for waste water treatment, which reduced the pollution loads significantly. A dose of 1.5 g/l of lime at p H 6.0 gave optimal results. Analysis results are represented in table 4. Average removal of BOD 5 was 66% where as COD reduction was found to be 65%. Lime treatment reduced t he TDS and TSS content to 56% and 60% respectively. It was inferred from the results that treatment with lime was effective and cheaper when compared with activated carbon. Apparently, there were some inherent problems with li me treatment. It increased th e pH of waste water. Temperature of waste water was also increased due to exothermic reaction of lime with water. However, such artifacts were not serious and could be addressed easily. (Helal Uddin et al., 2003). Table-4. : Pretreatment with commercial lime after sedimentation results (Iqbal et al., 2007) It was also apparent from the results that lime, th ough reduced the pollution loads significantly, it could not bring the concentration of BOD 5 and COD to the limits given in the National Environmental Quality Standards. 2.3.2-BIOLOGICAL TREATMENT OF WASTE WATER PRE-TREATED WITH LIME Analysis results of biological treatment of waste water pre-treated with lime are given in table 5. The biological treatment process in conjunction with c hemical treatment showed remarkable reduction in retention time and removal of BOD 5 and COD content of effluent. A 25% less retention time , when compared with the results of biological treatment of waste water pre-treated with activated carbon, gave 88% and 86% removal of B OD and COD content respectively . Whereas four days retention time resulted in 94% and 92% of BOD and COD loadings of the treatment effluent. (Aboulhassan et al., 2005 ; Shah et al., 2003). Table-5. Biological treatment of waste water Pre-treated with lime R.T(days) BOD (mg/l) COD (mg/l) Influent Effluent Removal % Influent Effluent Removal% 2 238 131 80 585 310 80 3 209 77 88 537 220 86 4 209 38 94 537 124 92 (Iqbal et al., 2007) Sample No 1 (mg/l) Sample No 2 (mg/l) Parameters Influent Effluent Removal % Influent Effluent Removal% PH 6 9.0 — 11 12.7 — TempC0 37 55 — 38 57 — BOD 662 238 64 675 209 69 COD 1582 585 63 1625 537 67 TDS 4650 2558 45 5030 2346 53 TSS 380 232 39 420 244 42 World Water Day April-2011 104 REFERENCES 1. Abadulla, E., Tzanov, T., Costa, S., Robra, K.H.,Cavaco, P.A., Guebitz, G.M., 2000. Decolorization and detoxification of textile dyes with a laccase from Trametes hirsuta. Appl. Environ. Microbiol. 66,3357 –3362. 2. Aboulhassan, MA., Souahi,S., Yaacoubi,A., Baudu,M.2005.Treatment of textile waste water using a natural flocculent. Environ Technol. 26: 705-711. 3. Chivukula, M., Renganathan, V., 1995. Phenolic azo dye oxidation by laccase from Pyricularia oryzae. Appl. Environ. Microbiol. 61, 4374 – 4377. 4. Chung, K.T., Stevens, S.E.J., 1993. Degradati on of azo dyes by environ – mental microorganisms and helminths. Environ. Toxicol. Chem. 12, 2121 – 2132. 5. Claus, H., Faber, G., Koenig, H., 2002. Redox -mediated decolorization of synthetic dyes by fungal laccases. Appl. Microbiol. Biotechnol. 59, 672 –678. 6. Dos Santos, A.B., Madrid, M.P., de Bok, F.A.M., Stams, A.J.M., Van Lier, J.B., Cervantes, F.J., 2006b. The contribution of fermentative bacteria and methanogenic archaea to azo dye reduction by thermo philic anaerobic consortium. Enzyme Microbiol. Technol. 3 9, 38–46. 7. Duran, N., Rosa, M.A., D ’Annibale, A., Gianfreda, L., 2002. Applica tions of laccases and tyrosinases (phenoloxidases) immobilized on different supports: a review. Enzyme Microbiol. Technol. 31, 907 –931. 8. Helal Uddin,A.B.M., Amat, S., Asri,M., M ohd, N.2003. Effectiveness of peat coagulant for the removal of textile dyes from aqueous solution and textile waste water. Malaysian. Journal of Chemistry. 5: 34-43. 9. Iqbal, M.K.,Nadeem,A.,Shafiq,T.,2007. Biological Treatment of Textile waste water by Activated Sludge Process. Journal of Chemical Society of Pakistan. 29: 397-400. 10. Lina, N., Abu, G., Ahmad, I.J. 2006. Biological treatment of textile waste water using sequencing batch reactor technology. Environ Model and Assess .11: 333- 343. 11. McMullan G, M eehan C, Conneely A, Kirby N, Robinson T, Nigam P,Banat IM, Marchant R, Smyth WF. 2001. Microbial decolourisation and degradation of textile dyes. Appl Microbiol Biotechnol. 56:81 –7. 12. Shah, V., Verma,P., Stopka,P., Gabriel,J., Baldrian, P., Nerud,F. 2003. Decolonization of dyes with copper (ii)/Organic acid/ hydrogen peroxide system. Appl.Catal.B: Environ. 46: 275-280. World Water Day April-2011 105 13. Stolz, A., 2001. Basic and applied aspects in the microbial degradation of azo dyes. Appl. Microbiol. Biotechnol. 56, 69 –80. 14. Turan-Ertas, T. 2001. Biological and physical –chemical treatment of textile dyeing waste water for color and COD removal. Ozone: Sci.Eng.23: 199-206. 15. Weisburger, J.H., 2002. Comments on the history and importance of aromatic and heterocyclic amines in public health. Mutat. Res. 506 – 507, 9–20. Fig.-3. Lab Scale Activated Sludge Rector Mode Fig.-4. Absorption Columns .
Filename:
Sustainable-Management-of-Textile-Waste-Water-of-Pakistan-1.pdf
File Type:
pdf
File Size:
316 KB
Categories:
World Water Day 2011
