110 FREE RADICAL GRAFTING OF METHACRYLIC ACID AND STYRENE ON LOW DENSITY POLYETHELENE By Muhammad Sarfraz* Abstract Binary mixture of methacrylic acid and styrene monomers, in presence of benzoyl peroxide as an initiator, were grafted o nto low density polye thylene. Characterization of the grafted polyethylene was accomplished using Fourier transform infrared spectroscope (FTIR), differential scanning calorimeter (DSC), and melt flow indexer (MFI). Presence of carbonyl peaks in the spectra of grafted polyethy lene, low MFI value as compared to pure polyethylene, and higher endothermic peaks in thermogram of grafted polyethylene affirmed grafting o f methacrylic acid and styrene onto polyethylene. It was observed that by increasing the amount of initiator, the melting point was increased. Keywords: Polyethylene, Grafting, Rheology, DSC (Differential Scanning Calorimeter) , FTIR (Fourier Transform Infrared Spectroscopy), HDPE (High Density Polyethylene), LDPE (Low Density Polyethylene), MFI (Melt Flow Index). 1. PAPER OBJECTIVE LDPE is the version of PE plastic (Thermoplastic) having low density . It has less strength, hardness, and density than those of HDPE, but more malleability [1-2]. LDPE is lighter than water, and can be machined, molded, articulated together using thermal welding but it is difficult to glue using an adhesive. Its appearance is wax -like, lackluster and opaque. The use of UV – stabilizers (carbon black) ameliorates its weather resistance but bouts it black. Some of its types can be applied in connection with the food stuffs [3]. LDPE shows bounded resistance against oxidizing agents and halogenated hydrocarbons and therefore, is suited for short term use only. In addition it shows inadequate UV resistance [4-5]. The existing modification techniques of polyolefins emphasize grafting as an enthralling method to confer a number of functional groups on to the surface of polyolefins [6, 8-9]. To attain certain characteristics we modify the structure of the base polymer. A large number of methods are being used to modify a polymer e.g. grafting (Copolymerization), mixing ( Composites). Extensive work has been done on grating of polyethylene to form a co -polymer [10-11]. These techniques include chemical, radiation, photochemical, plasma -induced and enzymatic grafting. Here in our experiment we have grafted two monomers (MMA, Styrene), in presence of BPO as initiator, on main chain of LDPE. Large work has been done on grafting of single monomer . But little work has been done on two monomers. So little bit information is available for the case of two monomer grafting. Number of researchers [13 -15] ha ve reported chemical grafting of exclusively one monomer on to polyethylene but minor work has been done on binary monomer mixture grafting especially by using a mixture of two monomers namely methacrylic acid and styrene. 2. EXPERIMENTAL 2.1 Materials Basic materials used in these experiments were low density polyethylene ( LDPE), meth acrylic acid (MAA), styrene, and benzyl peroxide (BPO). LDPE used here is a molded grade. 2.2 Synthesis of grafted polyethylene Weighed amounts of LDPE, styrene, water, and meth acrylic acid were placed in a round bottom flask. The mixture temp erature was increased up to 93 oC. As the desired temperature _____________________________________________________________________________________________ *Department of Polymer & Process Engineering, University of Engineering & Technology, Lahore-Pakistan. 111 was attained, BPO was added to the mixture and thorough agitation was carried o ut. The mixture was kept at the reaction temperature for a period of 3 -4 hours. After completion of reaction, product was washed with 0.1 N NaOH, dried, then washed with water, followed by washing with 0.1 N HCl, dried and then again washed with water. T he sample is then finally dried in an oven and further analysis was carried out. Then we prepare five more samples in a similar way but varying the concentration of initiator. In each of the subsequent samples we increase the amount of initiator by 0.25g while keeping all the other experimental parameters and quantities same. Composition of mixture is shown in Table 1. Table 1. Composition of mixture Materials S* 1 S* 2 S* 3 S* 4 S* 5 Methacrylic acid (ml) 12.75 12.75 12.75 12.75 12.75 Styrene (ml) 1.66 1.66 1.66 1.66 1.66 BPO (g) 0.75 1.0 1.25 1.50 1.75 Water (ml) 150 150 150 150 150 LDPE (g) 50 50 50 50 50 * S = Sample # 2.3 FTIR spectroscopy The FTIR spectrums were recorded on JASCO FT/IR -4100 infrared spectrometer. Potassium bromide was used as an inert background material to get the spectra of both pure and grafted samples of polyethylene. The analysis was done in the wave number region of 400 to 4000 cm1. 2.4 Differential scanning calorimetry DSC curves were obtained at heating rate of 10 oC min-1 in Shimadzu DSC 60 -An apparatus. Both pure and grafted samples were analyzed against aluminum as reference material. The temperature range for experiment was selected to be 180-190 oC. 2.5 Rheological testing MFI of the grafted and pure sampl es was determined by using MFI apparatus (KARG Industrietechnik) in accordance with the ASTM D 1238 -04 under load ranges of 1000 to 5000 grams for grafted sample awhile that of pure sample was determined under load ranges 500 to 3000 grams, with die diameter of 2.095 mm and at 190 oC temperature. 3. RESULTS AND DISCUSSIONS 3.1 Thermal Analysis Following histograms (given below) of pure LDPE and grafted samples show that an elevation in melting point occurs and melting point jumps from 130 oC to 131.85 oC and with further increase in initiator concentration it moves to 133.2 oC and becomes constant. This increase in melting point can be attributed to the presence of polar groups generated after grafting. Another important point is that this change in melti ng point, however, is relatively low and can be ascribed to low level of grafting. On a molecular level, the grafted chains are relatively difficult to move, rotate, and oscillate as compared to ungrafted ones; thus elevating the melting point of the material. 112 Figure 1. Thermogram of pure LDPE Figure 2. Thermogram of Grafted Copolymer having initiator concentration of 0.75 gm Figure 3. Thermogram of Grafted Copolymer of LDPE at 1.00 gm of initiator concentration 113 Figure 4. Thermogram of Grafted Copolymer of LDPE at 1.25 gm of initiator concentration Figure 5. Thermogram of Grafted Copolymer of LDPE at 1.50 gm of initiator concentration Figure 6. Thermogram of Grafted Copolymer of LDPE at 1.75 gm of initiator concentration 3.1.1 Percent Crystallanity Melting endotherms were observed during the heating cycle in the DSC scan for pure and grafted HDPE in the temperature range of 0 oC to 150 oC. 114 Melting endotherms were maneuvered in to determine the values of onset and peak temperatures along with their observed heat of fusion dH f obs values for both the vir gin and grafted samples (Table 2 ). The percentage crystallinity of the sample is calculated by use of following relationship: A value of enthalpy of fusion, dHf o, equal to 245 J/g for 100 % crystalline LDPE was used in above equation for calculating the percentage Crystallanity of both grades. Minute changes in melting temperature T m of HDPE were observed on addition of grafting agents. Heat of fusion and % Crystallanity of HDPE decreased with grafting. The Crystallanity has been decreased on account of the fact that with increase in grafting the crystal structure of pure sample gets distributed and results in the final lowering of decomposition temperature of grafted sample. After grafting of L DPE, the dispersed domains are produced that may act as a diluents resulting in decrement of values and the percent Crystallanity. Table 2 : Percent Crystallanity from heat of fusion values corresponding to onset temperature and peak temperature for virgin and grafted LDPE Sample χ (%) Pure LDPE 54.56 Grafted LDPE 0.75 gm BPO 52.23 Grafted LDPE 1.00 gm BPO 52.12 Grafted LDPE 1.25 gm BPO 51.56 Grafted LDPE 1.50 gm BPO 51.13 Grafted LDPE 1.75 gm BPO 50.83 3.2 Rheological Properties: Rheological measurements are very important for quality control of raw materials, optimization of manufacturing processes and forecasting the performance of a material. Melt flow index (MFI) is a good indicator of flow properties of the material under consideration. Figure 7 shows MFI of both graf ted and ungrafted polyethylene grades at different loads. It is evident from the Figure 7 that MFI of ungrafted polyethylene is more than grafted polyethylene at different loads. This decrease in MFI after grafting is associated with the greater degree of branching of grafted polyethylene as compared to ungrafted polyethylene. Presence of branches diminishes the flow properties in polyethylene up to much extent. This decrease in MFI is also an indication of efficient grafting of MAA and styrene on polyethylene. Higher viscosity of grafted LDPE than virgin LDPE is attributed to the presence of branches in grafted polyethylene which offer more hindrance to align themselves in the flow direction on applying stress as compared to the more flexible straight chai ns in ungrafted low density polyethylene. Grafted chains make some sort of physical entanglements among themselves which stand firm against applied stress, thus increasing melt viscosity. This decrease in viscosity with increasing strain rate reveals rheopectic behavior. 115 Figure 7. Effect of temperature on Melt flow Index Note: Upper curve (grafted sample); lower curve (pure LDPE) Figure 8. Effect of Load on Melt flow Index Note: Upper curve (grafted sample); lower curve (pure LDPE) 3.3 Structural Analysis From FTIR results, it is obvious that by the grafting of LDPE with styrene and methyl methacrylate, frequency changes which reveals the change of functional group of aromatics and hydrocarbons (C-H). Figure 9. FTIR Spectrum of Pure LDPE 116 Figure 10. FTIR Spectrum of Grafted LDPE having 0.75 gm initiator concentration Figure11. FTIR Spectrum of Grafted LDPE having 1.00 gm initiator concentration Figure 12. FTIR Spectrum of Grafted LDPE having 1.25 gm initiator concentration 3.3.1 Degree of Grafting Degree of grafting is defined as the extent to which the original polymeric sample has been grafted. The degree of grafting of methacrylic acid -grafted-LDPE sample is found by simply 117 measuring the change in weight of the grafted sample after complete drying. Percent degree of grafting can be calculated from the following relationship: Where ĝ is the percent degree of grafting of LDPE, Es is the equivalent weight of styrene and Eg is the equivalent weight of grafted LDPE. Values of percent degree of grafting for different samples are given below as shown in Table 3. Table 3: Percent degree of grafting of LDPE grafted with different amounts of initator Serial # BPO (gram) ĝ (%) 1 0.75 27.21 2 1.00 27.35 3 1.25 27.74 4 1.50 28.03 5 1.75 28.78 4. CONCLUSION 1. The above discussion reveals that a reasonable amount of grafting achieved using Styrene and MMA using BPO (as an initiator) and Rheological properties have been changed due to grafting process which is indicated by lower value of MFI of grafted polyethylene as compare to virgin LDPE. 2. For same strain rate, higher stress is required f or grafted polyethylene as compared to virgin polyethylene due to resistance in flow offered by branched chains. 3. Viscosity also increases by introduction of branches. 4. From DSC analysis, it is concluded that melting point of LDPE increases after grafting. 5. As we increase the concentration of initiator so little effect on properties observed, but grafted material becomes more brittle than pure LDPE. 5. ACKNOWLEDGEMENT The authors are thankful to the Department of Polymer and Process Engineering, Uni versity of Engineering and Technology Lahore -Pakistan for furnishing laboratory equipment and related chemicals and materials. 6. REFERENCES [1]. Daniel J. Burnett, Frank Thielmann, Rose A. Ryntz,Correlating thermodynamic and mechanical adhesion phenomen a for thermoplastic polyolefin, Springer Boston,2007.4(2) :PP 211-215. [2]. Shrojal M. Desai, R. P. Singh, Advances in polymer science, Springer Berlin / Heidelberg, 2004.169: PP 231-294 [3]. S.K.Singh, S.P.Tambe, A.B.Samui, V.S.Raja, Dhirendra Kumar, M aleic acid grafted low density polyethylene for thermally sprayable anticorrosive coatings, Progress in organic coatings,2006.55(1):PP 20-26 118 [4]. Gilberto de O.Meraes,Adriana N.Geraldes,Heloisa A.Zen,Duclerc F. Parra, Ademar B.Lugao,Preliminary study of s tyrene grafting on Polyethylene films, International Nuclear Atlantic Conference ,2007 [5]. A. Shojaei, R. Fathi, N. Sheikh, Adhesion modification of Polyethylene for metallization using radiation induced grafting of vinyl monomers, Surface & coating tech nolgy, 2007.201: PP 7519-7529 [6]. A. Bhattacharya, B.N. Misra, Grafting; a versatile means to modify polymers techniques, factors and applications, Progress in polymer science, 2004.29: PP 767-814 [7]. Franjo Ranogajec, Effect of solvent on radiation gr afting and crosslinking of polyethylene, Radiation physics & chemistry, 2007.76: PP 1381-1384 [8]. Yoshikimi Uyama, Koichi Kato and Yoshito Ikada, Surface modification of Polymers by grafting, Advances in polymer science, Springer Berlin/Heidelberg, 1998.137: PP 1-39 [9]. A. Baran Teke, S. Hamarat Baysal, Immobilization of urease using glycidyl methacrylate grafted nylon-6 membranes, Process biochemistry, 2007.42: PP 439-443 [10]. K Yamada, T Kimuro, H Tsutaya, M. Hirata, Hyrophilic and adhesive properties of methacrylic acid grafted polyethylene plates, Journal of applied polymer science, 2003.(44)1: PP 993-1001 [11]. Ging -Ho Hsiue, Wen -Kuei Huang, Preirradiation grafting of acrylic and methacrylic acid onto polyethylene fi lms: Preparation and properties, Journal of applied polymer science, 2003(30) 3: PP 1023-1033 [12]. J.P. Lawler, A Charlesby, Grafting of acrylic acid onto polyethylene using radiation as initiator, Radiation physics & chemistry, 1980.(15)5: PP 595-602 [13]. O.N. Tretinnikov,Analysis of photo induced graft polymerization of acrylic acid onto polyethylene films by attenuated total reflectance IR spectroscopy, Journal of applied spectroscopy, 2010.(76)6: PP 898-901 [14]. Shenoy AV and Saini DR, Thermoplastic melt rheology and processing, CRC Press, 1996 [15]. Cogswell F.N, Polymer melt rheology: a guide for industrial practice, G. Godwin, 1981
Filename:
18-Free-Redical-Grafting-of-Methacrylic-Acid-and-Styrene-on-Low.pdf
File Type:
pdf
File Size:
297 KB
Categories:
Volume 0043
