Pakistan Engineering Congress, 69th Annual Session Proceedings 409 USING ENVIRONMENT FRIENDLY FINELY DIVIDED MATERIALS IN BRITTLE MATRIX COMPOSITES Syed Ali Rizwan1, Husnain Ahmad2 1. ABSTRACT Material engineers the world over are increasingly recommending the use of environment friendly efficient construction materials, which otherwise would have been classed as waste materials for improving the durability of concrete. Pakistan has been blessed by nature with huge natural resources of lime, and fly-ash is also becoming increasingly available with the induction of thermal power generation plants. To introduce the benefits of such concrete modifying materials to the engineering community in our country, an investigation has been carried out on the use of locally available powdered hydrated lime, fly-ash and their combinations in making concretes with a view to evaluate their strength, workability, durability a nd cost effectiveness. As such there is no documented data of local materials available on the topic in Pakistan. ACI (10) mentions powdered hydrated lime and fly–ash as finely divided admixt ures which can be used to improve concrete properties at microstructure level. It is commonly believed by the engineers that the use of such materials is especially desirable for durability purposes. Moreover, lime when added in concrete absorbs CO2 from the environment thus making it friendly flexible material. The results of investigation are encouraging especially when the two were used in combination as some weight fraction of cement to make quality and environment friendly concrete. Key Words: Concrete Lime, Fly–ash, Admixtures, Environment friendly, finely divided, Workability, Corrosion, Carbonation and Durability. 2. INTRODUCTION It is well known that modification of cons truction materials always aims at some predetermined and carefully selected objective/(s). The choice of admixtures to be used also depends upon the objective/(s) of modification which may e ither be for strength, architectural finishes, concrete conveyance, placing, permeability, durability or a combination of these in addition to their availability(1,2) As reported by ACI (10) titled “Guide for use of Admixtures in/ Concrete”, finely divided mineral admixtures include hydrated powdere d lime, fly-ash ground quartz, ground limestone, bentonite and talc. If concrete aggregates are deficient in fine particle sizes particularly those passing BS sieve 100 and 200, the use of finely divide d mineral admixtures can reduce bleeding and segregation and increase in strength while reverse may also be true if these are used for concrete 1 Syed Ali Rizwan is a Professor of Civil Engineering, Univ ersity of Engineering and Technology (UET) Lahore–54890, Pakistan. M.ASCE. Email: syedalirizwan@hotmail.com. He is an internationally renowned engineer for his research focusing mainly on Design, repair, maintenance and load testing of structures, concrete admixtures and space structures. 2 Husnain Ahmad, Executive District Officer, Information Technology Department, City District Government Lahore. Email: husnainahmad@hotmail.com Rizwan, Ahmad 410 aggregate not deficient in fine aggregates in said range suggesting that its use should be made under supervision of a good material engineer. Lime and fly-ash as independent admixtures and their combination has been used for modifying the concrete properties and a long term research has been conducted by the researchers to exploit the properties of locally available lime and fly-ash (1, 2). There are huge resources of natural lime available in Pakistan. Lime has been used in the construction industry since prehistoric period but its use in concrete as finely divided admixtures has explored its new properties and uses. There are many misconceptions about form of lime to be used in construction. For use in mortar/concrete, lime was produced by heating calcium carbonate (lime stone, chalk, shells and corals etc) in kiln to a temperature of approximately 900ºC-1100C0 .At this temperature, CO2 is driven off and calcium carbonate changes to calcium oxide (quick lime) due to calcinations process(6). When this calcium oxide (CaO) was slaked with water it formed calcium hydroxide or lime putty when excessive water was added. However if adequate amount of water was added with heat supplied it gave powdered hydrated lime of type S when crushed and screened through very fine sieves. Powdered hydrated lime of type S is basically used in mortars and concrete to reduce the permeability of concrete by filling the pores in concrete. It improves cohesion and achieves economy through cement replacements. It can also be used in hot weather concreting. (7, 8, 14). In addition to mineral admixtures, synthetic polymers can also be used to improve durability and other properties of concrete (11, 12,13). The authors have also carried out research on this type of modified concrete and its details can be found else where (3, 4, 5) 3. FLY–ASH Fly ash is a byproduct of burning finely divided coal in electrically generating power plants. It is captured from exhaust gases of power plants by electrostatic precipitation, which enables the relatively clean air to escape from smoke. Fly ash is rich in oxides of silica, alumina and iron. Chemically speaking, “FLY ASH LOOKS FOR LIME” when mixed with cement in presence of water. 100 kg of Portland cement when mixed w ith water liberates12-20 kg of free lime (CaO) during hydration. Fly ash with its chemically active silica and alumina readily reacts with this free lime to form additional cementitious compounds. When used in concrete, fly ash acts like cement, and actually replaces a percentage of the Portland cement used. Fly ash generally replaces around 15% of cement in much of the concrete used today, but we can do much better by using it to replace up to 50% or more (17) to be known as High Volume Fly Ash Concrete (HVFAC) Modification with Fly ash usually results in cement savings, increased workability, increased strength after 56 days, increased cohesion of mix, pore refinement, increased frost and chemical resistance and reduced permeability of concrete etc, which makes a high performance concrete. The above desirable properties are achieved because of its spherical shape and fineness. About 40% of fly-ash particles are under 10 microns while size of cement particle is 20 microns. Pakistan Engineering Congress, 69th Annual Session Proceedings 411 Fig (a) Fly-ash particles at higher magnification. Fig (b) Same at lower magnification When fly ash is added to the m ix, the silica in fly-ash reacts with these large crystals of Ca(OH)2 and transforms them into a strong cement paste that binds concrete together. SiO2 + Ca(OH)2 Æ CaO.SiO2.H2O (CSH- calcium silicate hydrate) This eliminates the micro cracking and creates concrete that is m uch less permeable, and therefore more durable. Also, a reinforced cement concrete modified with fly-ash will be less prone to less corrosion as it decreases the ingress of wate r to a greater extent which actually causes the corrosion of rebars in reinforced concrete. The fly-ash and lime are waste materials which may be a source of environmental concern if allowed to be spread near their place of manufacture. If used properly in construction, it would be an environmentally friendly efficient construction solution. The chemical composition of the fly-ask was a time consuming chemical process and therefore could not be done till the completion of this study. 4. USES OF LIME There are m any m isconceptions about uses of powdered hydrated lim e in construction industry and valuable research works all over the world and this m aterial has proven to be an important mineral admixture in the construction industry. Lime can be used both in m ortars and concretes for a number of useful purposes. Lime imparts a high water retentivity and reduces size of voids by accom modating itself in them . Som e res earchers have stated that bond strength also increases by using hydrated lim e in concrete. Hydrated lim e slightly decreases plasticity and workability of concrete. It imparts ease of re-tempering, high water retentivity, resistance against efflorescence, high sand carrying capacity and more flexibility under stress, more bond strength and autogenous healing to the mortars. Also lighter and colored mortars can be made by using hydrated lime along with a suitable pigment. Uses of lim e include soil m odification a nd stabilization, specially in pavem ents, environmentally friendly construction, paperm aking, production of chem icals (sodium alkalis, calcium carbide, calcium hypochlorite, citric acid, petro-chemicals, refractories, sugar refining, glass making, softening of drinking water, sewage tr eatment, agricultural fertilizers, fungicidal and insecticidal action, steel fluxing, bleaches, separati on of cream from whole milk and in handling chicken litter etc. Rizwan, Ahmad 412 5. USES OF FLY-ASH Engineers have an interest in using fly as h on a routine basis to improve the quality of concrete and to increase cost effectiveness . Fly ash can compensate fo r fines not found in some sands and, thereby, enhance pumpability and concrete finishing. It results in a more predictable and consistent finished product which will ensure customer acceptance. It improves the flowability of concrete which translates into less wear and tear on the entire producer’s equipment from batching facilities to trucks. Fly ash enables the producer to customize designs to each customer’s needs, thus providing the producer who uses it with a competitive advantage. The addition of fly ash to the mix is a built-in insurance for later-age strength gain in concrete and ensures that the concrete will qualify as a durable building material. Fly ash contributes to the aesthetic appearance of the concrete. (15, 16). The workability of fly ash concrete generally ensures that the speed of construction is faster which translates into a quicker return on investment. Since fly ash concrete is not as vulnerable to deterioration or disintegration as rapidly as concrete without fly ash, it ensures low-maintenance buildings which will retain thei r value over the long-term. Fly ash definitely enhances quality of concrete construction and returns real benefits to every member of the building team. 6. CASTINGS In order to study the parameters mentioned above for both normal (control), lime modified, fly-ash modified and combination of both lime and fly-ash concretes specimens were cast in both rich and lean concrete mixes i.e 1:1.5:3, 1:2:4and 1:2.5:5 concrete mix proportions by weight having net water-cement ratio (W/C) of 0.6 at a room temperature of 340C and relative humidity of 55 %. Locally available Haro sand with a fineness modulus of 2.60 on ASTM Sieve 100 (BS sieve 100) and Margallah crushed stone(lime stone or calcium carbonate) 3/4”or19.5mm down having a fineness modulus of 6.6 on sieve 100 were used. In the lime modified concrete, lime was added to the mixes of concrete of 1:1.5:3, 1:2.5:5 propor tions as 10% by weight of cement ACI-211 [10] . Details of various types of modified concretes can be seen elsewhere [3, 4, 5) On the similar lines, concretes were modified with fly-ash and specimens were cast using fly- ash equal to 10% of weight of cement. Mixes with a combination of fly-ash and lime (cocktail) were also cast (5 % lime and 5 % fly-ash) with a total of 10% as addition-not replacement) of weight of cement. The castings included 100x100x100 mm (4”x 4”x 4 ”) cubes and 150mm (6”) diameter standard cylinders for compression testing and 50x50x50 mm (2”x 2”x 2”) cubes for %age water absorption and durability tests. The coarse aggreg ates had an apparent specific gravity of 2.63. Coarse aggregates comprised crushed stone (3 /4” or 19.5mm down) from Margallah Hills. Fine aggregates consisted of sand of river Haro sand having a fineness modulus of 2.6.Cement; lime and sand were mixed in a pan type mixer in laborator y in the presence of 50% water content to avoid their escape in form of dust. Then coarse aggregates and remaining water content was added. Total mixing time was about 4 minutes. Table 1and 2 give the bulk densities of constituent materials, their specific gravities while Tables 3,4 and 5 give workability test results. Pakistan Engineering Congress, 69th Annual Session Proceedings 413 Table No1:- Bulk Densities of Constituent Materials Material Loose State (Kg/m3)/( Lbs/ft3) Rodded State(Kg/m3)/(Lbs/Ft3) (K / 3) / (lb/ft³) Haro/Lawrencepur Sand 1433.8 / 89.61 1586.0 / 99.12 Coarse aggregate (19 mm) down) 1418.3 / 88.64 1595.6 / 99.72 Cement 1435.4 / 89.71 Not Determined Lime 649.8 / 40.61 do Fly ash 933.58 / 58.31 do Cocktail(lime+fly-ash) 799.25 / 49.92 do Table No 2:- Specific Gravities of Constituent Materials. Material Specific Gravity Crush 2.63 Sand 2.63 Cement 3.15 Lime 2.173 Fly-ash 2.562 Cocktail 2.515 Table No-3: Results of Workability Test for Lime Modified Concrete Type of Test Type of Mix W/ C ratio Normal Concrete Modified Concrete 1:1.5:3 0.6 2.5 3 Slump Test (in) 1:2.5:5 0.6 0 0 1:1.5:3 0.6 0.984 0.99 Compacting Factor Test 1:2.5:5 0.6 0.802 0.763 Rizwan, Ahmad 414 Table No-4: Results of Workability Test for Fly-Ash Modified Concrete Type of Test Type of Mix W/ C ratio Normal Concrete Modified Concrete 1:1.5:3 0.6 2.5 0.5 Slump Test (in) 1:2.5:5 0.6 0 0 1:1.5:3 0.6 0.984 0.8 Compacting Factor Test 1:2.5:5 0.6 0.802 0.7 Table No-5: Results of Workability Test fo r Fly-Ash and Lime Combination Cocktail Modified Concrete. Type of Test Type of Mix W/ C ratio Normal Concrete Modified Concrete 1:1.5:3 0.6 2.5 2.8 Slump Test (in) 1:2.5:5 0.6 0 0 1:1.5:3 0.6 0.984 0.99 Compacting Factor Test 1:2.5:5 0.6 0.802 0.739 7. CURING OF SPECIMENS For the first 24 hours after casting, the specimens were kept in moulds at 100% RH in the curing room maintained through showers. They were de-molded after 24 hours. Thereafter all the specimens were kept in water for 28 days. After th at, they were taken out of water and kept at normal laboratory conditions and tested at specified ages. Tables 6, 7, 8 and 9 give the results of compressive strength of cylinders and cubes at different ages. Fig Nos 1 and 2 give the age-strength relationships of lime and fly-ash modified concretes. Table No-6:-Comparative Results of Compressive Strength for Lime Modified Concrete Crushing strength (Psi) Mix Design Lime Added Size of Specimen 3 days 7 days 28 days 56 days 1:2.5:5 10% of cement 6”Φx 12” Cylinders 3137 3925 4713 — 1:2.5:5 10% of cement 4”x 4”x 4” 4838 5110 5600 7163 1:2.5:5 Control Mix 0% of cement 4”x 4”x 4” 2548 3030 3719 5373 Pakistan Engineering Congress, 69th Annual Session Proceedings 415 Table No-7:- Comparative Results of Compressive Strength for Lime Modified Concrete Crushing strength (Psi) Mix Design Lime Added Size of Specimen 3 days 7 days 28 days 56 days 1:1.5:3 10% of cement 6”Φx 12” Cylinders 2634 2882 3684 – 1:1.5:3 10% of cement 4”x 4”x 4” 3395 4025 4550 6612 1:1.5:3 Control Mix 0% of cement 4”x 4”x 4” 2538 3101 3753 5785 Age ~Comparitve Compressive Strength Relationships for Lime modified Concrete 0 1000 2000 3000 4000 5000 6000 7000 8000 0 7 14 21 28 35 42 49 56 63 Age (days) Compressive Strength (psi) Lime Modified Concrete (1:2.5:5) w/c=0.6″ Cont rol Mix (1:2.5:5) w/c=0.6 Lime Modified Concrete (1:1.5:3) w/c=0.6″ Cont rol Mix (1:1.5:3) w/c=0.6 Fig .No. 1 Comparative Compressive strength- Age relationships of lime modified concrete Table No-8: – Comparative Results of Compressive Strength for Fly-Ash Modified Concrete Crushing strength (Psi) Mix Design Fly-ash Added Size of Specimen 3 days 7 days 28 days 56 days 1:2.5:5 10% of cement 6”Φx 12” Cylinders 1830 2124 3071 — 1:2.5:5 10% of cement 4”x 4”x 4” 3271 3719 4133 4476 1:2.5:5 Control Mix 0% of cement 4”x 4”x 4” 2548 3030 3719 5373 Rizwan, Ahmad 416 Table No 9:- Comparative Results of Compressive Strength for Fly-Ash Modified Concrete Crushing strength (Psi) Mix Design Fly-ash Added Size of Specimen 3 days 7 days 28 days 56 days 1:1.5:3 10% of cement 6”Φx 12” Cylinders 2445 3407 4015 — 1:1.5:3 10% of cement 4”x 4”x 4” 3271 4375 5131 5650 1:1.5:3 Control Mix 0% of cement 4”x 4”x 4” 2341 3185 3753 5785 Age ~ Comparitive Compressive S trength Relationships for Flyash Modified Concrete. 0 1000 2000 3000 4000 5000 6000 7000 0 7 14 21 28 35 42 49 56 63 Age (days) Compressive Strength (psi) Flyash modified concrete (1:2.5:5) w/c=0.6 cont rol mix (1:2.5:5) w/c=0.6 flyash modified concrete (1:1.5:3) w/c=0.6 cont rol mix (1:1.5:3) w/c=0.6 Fig No 2. Comparative compressive strengths of fly-ash modified concrete Table No-10: Comparative Results of Co mpressive Strength for Fly-Ash and Lime Combination (cocktail) Modified Concrete Crushing strength (Psi) Mix Design Fly-ash & Lime Combination Added Size of Specimen 3 days 7 days 28 days 56 days 1:2.5:3 Each 5 % of cement 6”Φx 12” Cylinders 2546 2944 4056 — 1:2.5:3 Each 5 % of cement 4”x 4”x 4” 3185 4217 4787 5950 1:2.5:3 Control Mix 0% of cement 4”x 4”x 4” 2391 3255 4030 5373 Table No-11: Comparative Results of Co mpressive Strength for Fly-Ash and Lime Pakistan Engineering Congress, 69th Annual Session Proceedings 417 Combination Modified Concrete Tables No 10 Table and 11 give the strength-age relationships for cocktail modified concrete made in 1:2.5: and 1:1.5:3, W/c=0.6 Crushing strength (Psi) Mix Design Fly-ash & Lime Combination Added Size of Specimen 3 days 7 days 28 days 56 days 1:1.5:3 Each 5 % of cement 6”Φx 12” Cylinders 2595 3049 4063 — 1:1.5:3 Each 5 % of cement 4”x 4”x 4” 3679 4511 5578 6825 1:1.5:3 Control Mix 0% of cement 4”x 4”x 4” 3376 4235 5062 6832 Age ~ comparative Compressive Strengths for Cocktail Modified Concrete 0 1000 2000 3000 4000 5000 6000 7000 8000 0 7 14 21 28 35 42 49 56 63 Age (days) Compressive Strength (psi) Cocktail Modified Concrete (1:2.5:5) w/c=0.6 Cont rol Mix (1:2.5:5) w/c=0.6 Cocktail Modified Concrete (1:1.5:3) w/c=0.6 Cont rol Mix (1:1.5:3) w/c=0.6 Fig No 3 Strength-age relationships of cocktail modified concretes. 8. CHEMICAL RESISTANCE OF NORMAL AND MODIFIED CONCRETES Acid resistance test was performed on 2”x2”x2”( 50x50x50mm) specimens cut from original 4”x4”x4”(100x100x100mm) cubes against N/2 solutions of HCl, HNO3 and H2SO4. The procedure for making N/2 acid solutions is as follows. 1. Find the density of acid by using specific gravity flask/pycnometer. 2. Determine the percentage purity of acid from standard tables against density values either directly or by interpolation. 3. Find equivalent weight of acid i.e. by using formula, Equivalent Weight = Molecular weight/number of hydrogen ions. For example for H2SO4, the molecular weight is 98 (2 for H2, 32 for S and 4×16=64 for O4) divided by 2(number of hydrogen ions) equals 49.Compute density of 1N solution by following Rizwan, Ahmad 418 formula. Density of 1N solution = (equivalent w eight of acid x 100) / (density of acid x % age purity of acid) 1. This density represents the am ount of acid in grams to be added in water to m ake total volume as 1litre. 2. We can determine the volume of acid required by the following expression. Volume = Weight / Density 9. TEST PROCEDURE: The specimens were immersed in acid solution, an immediate reaction took place and after one week, the solution became weaker and was changed. This was repeated four times during 28 days cycle and pH changes were monitored during this cycle by means of pH sticks or by uusing pH meter. After 28 days weight loss indicated degr ee of vulnerability or indirect durability as per recommendations of international literature (12). The results of acid resistance are given below. Table No 12- Acid Resistance Test Results 1: 1.5: 3, W/C= 0.6 Acid Sample Initial Weight Weight after 28 Days % Weight Loss lime 292.52 277.6 5.10 HCl fly-ash 270.72 261.75 3.31 cocktail 266.62 257.32 3.48 control 250.17 236.18 5.59 lime 270.61 255.94 5.42 H2SO4 fly-ash 288.65 273.19 5.35 cocktail 318.58 303.71 4.66 control 293.8 273.34 6.96 lime 269.6 249.08 7.61 HNO3 fly-ash 325.54 287.97 11.54 cocktail 311.55 291.77 6.34 control 296.22 285.63 3.57 Comparison for % Weight Loss in Acid Resistance Test on 1:1.5:3 (w/c=0.6) Mix 0.00 2.00 4.00 6.00 8.00 10.00 12.00 14.00 Conrol Mix FlyA sh Lime Cocktail Admixture Used % Weight Loss HCl H2SO4 HNO3 Fig 4 Results of acid resistance tests on control, lime, fly-ash and cocktail modified concretes of 1:1.5:3.0, w/c = 0.6 concrete. Table No. 13:- Acid Resistance Test 1:2.5:5, W/C=0.60 Pakistan Engineering Congress, 69th Annual Session Proceedings 419 Acid Sample Initial Weight Weight after 28 Days % Weight Loss lime 279.15 269.44 3.48 HCl fly-ash 277.81 264.08 4.94 cocktail 260.23 247 5.08 control 291.85 280.76 3.80 lime 319.75 307.7 3.77 H2SO4 fly-ash 274.22 261.07 4.80 cocktail 297.84 288.5 3.14 control 288.36 275.3 4.53 lime 264.56 245 7.39 HNO3 fly-ash 272.86 252.08 7.62 Cocktail 273.12 253.23 7.28 Control 282.91 263.18 6.97 Comparison for %age weight Loss in acid resistance test on 1:2.5:5 (w/c=0.6) Mix 0.00 2.00 4.00 6.00 8.00 10.00 Co nrol Mi x FlyAsh Lime Co cktail Admixture used % Weight Loss HCl H2SO4 HNO3 Fig 5. Acid resistance test results on 1:2.5:5.0, w/c=0.6 concrete. 10. DISCUSSION From the behavior of fly-ash it appeared to be of class F accor4ding to ASTM classification because for class C fly-ash Bulk density is usually low. Increase of workability due to addition of lime m ay be attributed to its fine-ness and no water dem and com pared with fly-ash m odified concrete in which workability reduces due to water demand of fly-ash. Addition of lime and fly-ash increases the strength of lime and fly-ash modified concretes. This may be understood to be the fact due to “packing effect” of the voids in the pr oducts of hydration. Lim e and fly-ash m odified concretes present variable results f or the bot h m ixes against three acids and no well defined conclusion may be made. Against HCL and H2SO4 control concrete gives more weight loss while for HNO3 control concrete gives least weight loss. 11. CONCLUDING REMARKS Rizwan, Ahmad 420 1. Use of fly-ash and lime in concrete results in economical-high performance concrete. 2. The results are only for the materials and mix proportions used. For other mix proportions, same results may not be applicable. 3. Compressive strength of concrete increase with an increase in %age of this type of fly-ash and lime as an addition of some percentage of cement in concrete at early ages 4. Permeability, durability and cohesion of concrete in general are improved with the addition of mineral admixtures studied. 5. Workability of concrete is increased when fly as h is added to it but situation is reverse with lime. 6. For better results, it is recommended that lime and fly-ash should be batched on volume basis for mixing in concrete. If taken as a weight percent of cement, lesser percentages may give still better results. 7. From acid resistance tests on cut specimens, it became clear that acids attack severely the coarse aggregates (lime stone). The attack on the paste was that serious for N/2 normality. ACKNOWLEDGEMENTS Thanks are due to my final year students Mr. Aun and Mr.Mohsin for their help during experimentation and compilation stages. Thanks are due to Engr Azhar Ali Bhatty Director Designs, M/s Izhar Constructions (Pvt) Ltd. Tipu Block New Garden Town Lahore for providing fly-ash and powdered hydrated lime used in this study. REFERENCES 1. Rizwan,S.A., Toor, Shamas-ur-Rehman and Ahmad, H . “Using Locally Available Fly Ash For Modifying Concrete Properties ” Proc 69th Annual session of Pakistan Engineering Congress, Vo69, Oct 19-21, 2003,Lahore, Pakistan Paper No. 2. Rizwan,S.A., Toor, Shamas-ur-Rehman and Ahmad, H . “Exploiting the Huge Resources of Lime in Pakistan for Construct Industry” Proc 68 th Annual session of Pakistan Engineering Congress, Vo69, Oct 19-21, 2003,Lahore, Pakistan Paper No 3. Rizwan,S.A., Hameed, A. and Ahmad,K. “Latex Modified High Performance Concrete” Proceedings of 6th International Sym posium on High Strength/High Performance Concrete,Volume-2, pp 1313-1324,University of Leipzeig, June 2002,Germany. 4. Rizwan,S.A., and Hameed, A. “ Comparative Response of SBR Latex Modified Concrete” 6th International Congress on Changes to Concrete Construction, July 2002, Proc titled “Sustainable Construction”, pp 162-169,University of Dundee, Scotland, U.K. 5. Rizwan S.A., Ahmad,A and Ahmad,K ” A Comparative study of modified concretes” . Proc 68th Annual session of Pakistan Engineering Congress, Vo68, Jan 19-21, 2001,Lahore, Pakistan Paper No. 621 pp 313-323 6. Boynton,R.S “ Chemistry and Technology of Lime and Limestone”. Second Edition 1980, John-Willy and Sons.USA. 7. Cowper,A.D “ Lime and Lime Mortar”, Don Head Publishing Ltd.Jan 1998. 8. R,Klus and Wynne,C “Building that Changed the World” Pestel Publishing Sept 1999. Pakistan Engineering Congress, 69th Annual Session Proceedings 421 9. ACI Committee-211 “ Selecting the normal weight concrete mix proportions” 10. ACI Committee -212, Admixtures in Concrete, American Concrete Institute,Detroit,1973. 11. ACI Committee 548, “ Polymers in Concrete ”, Publication SP-40 and SP-58, American concrete institute, Detroit, 1973. 12. Ohama, Y., and Miyake, M. : Resistance of Polymers modified Concrete to Inorganic Acids” National Symposium on Binder Economy a nd Alternate Binders in Road and Building Construction,1981, Japan 13. ACI – 548 “ State of the Art Report on Polymer Modified Concrete”. ACI – 548.3 R-95. 14. Hielenz, R.C “ Mineral Admixtures – History and Background”, Concrete International Journal, August 1983, pp (34-68). 15. Cook ,J.E “ Fly ash in Concrete-Technical Considerations ”, Concrete International Journal. Sept 1983, pp (51-60). 16. Swamy, R.N “ Fly ash Concrete – Potential without Misuse”, ACI Journal of Materials and Structures, 1990,No 23, pp (397-411). 17. Melhotra, V.M, Corret, G.G and Langley, W.S “ Structural Concrete Imparting High Volume of ASTM class F-fly ashes”, ACI Materials Journal, Title No 88-448, September- October 1989, pp (507-513). RELATED INTERNET LINKS • British Lime Association, http://www.bla.com • Building with Lime, www.itdg.org • slct@scotlime.org

Filename: 656.pdf
File Type: pdf
File Size: 279 KB
Author: Husnain Ahmad, Syed Ali Rizwan